IKO Flashing Replacement Nationwide

IKO Flashing Replacement: The Los Angeles Owner’s Guide

IKO flashing replacement in Los Angeles typically runs $450 to $1,100 installed, depending on roof pitch, accessibility, and how much surrounding material has to come up. We stock IKO-compatible flashing on the truck and can usually complete the swap the same day we diagnose it. Most Los Angeles homeowners find out their flashing has failed the hard way: a water stain on the ceiling after the first real rain of the season, or a musty smell in the attic that wasn’t there in September.

Call (361) 320-9467

Flashing is the metal that seals the joints where your roof meets a wall, chimney, skylight, or valley. When it fails, water gets behind it and starts working on your decking and underlayment. Here’s the thing about Los Angeles weather: we go months without rain, then get hammered for a week straight. Flashing that’s been quietly corroding through a dry summer becomes a visible problem the moment the storms arrive. Travis Oakley has pulled flashing off hillside homes in Studio City that looked fine from the ground and crumbled in his hand on the roof. The sun and marine layer do a number on unprotected metal over time, and IKO flashing is no exception, especially on the older Cambridge and Dynasty runs from the early 2000s.

Which IKO Models This Applies To

IKO’s flashing products are designed to work with their architectural shingle lines, including Cambridge, Dynasty, Nordic, and Royal Estate. The good news is that most IKO flashing profiles follow standard industry dimensions rather than proprietary shapes, which means a correctly sized replacement from a quality manufacturer will match the original without fuss. That said, there’s one compatibility detail worth knowing: IKO’s self-adhesive flashing tapes and underlayments are engineered for their shingle chemistry, but the metal flashing itself, step flashing, pipe collars, and valley metal, are interchangeable across brands when the gauge and dimensions line up.

If your house was built or re-roofed in Los Angeles between roughly 2005 and 2018 with IKO shingles, you’re likely dealing with galvanized steel flashing in the 26 to 28 gauge range. Some higher-end installs used aluminum. The simplest way to identify what you have is to check the roof for an IKO warranty sticker or a leftover bundle label in the garage, then measure the exposed flashing face. Standard step flashing is 5 inches by 7 inches with a 2-inch face. Pipe collars are either 1.5 or 2 inches depending on the vent stack. When we replace IKO flashing, we match the original gauge and adjust for anything that’s changed since, like a new stucco wall or a chimney repoint. OEM IKO flashing is available through supply houses, but in practice we install GAF, Owens Corning, or CertainTeed flashing on IKO roofs routinely. Metal is metal when the spec matches, and the alternative usually costs less without giving up anything where it counts.

Signs Your IKO Flashing Replacement Is Failing

• Water stains on ceilings or upper walls after rain. This is the classic. Water travels along the underside of the roof deck and shows up ten feet from the actual leak. The flashing at a valley or headwall is almost always the culprit when stains appear in a straight line along one wall.
• Rust streaks or pitting on visible metal. Los Angeles air carries salt from the coast and pollutants that settle into the basin. Galvanized flashing eventually loses its zinc layer, and once the base steel is exposed, rust follows. If you can see flaking or orange staining from the ground on a two-story, it’s already too far gone to patch.
• Lifted or separated flashing at the chimney or skylight. Thermal expansion works metal back and forth for years. The old tar or caulk bead that sealed the flashing to the masonry eventually splits. On a hot LA afternoon, you can sometimes see a visible gap where the flashing lifts off the chimney face.
• Granule loss concentrated around penetrations. Shingles near vents, pipes, and chimneys wear faster when water isn’t being directed away properly. If you see bare spots on shingles right around a pipe boot or chimney flashing, the flashing has likely been channeling water onto the shingle surface instead of into the gutter path.
• Attic dampness or mold smell without an obvious roof leak. Slow flashing leaks don’t always produce a visible stain. They saturate the decking and underlayment over months, and what you notice first is the smell. We’ve pulled up flashing in Eagle Rock where the decking underneath was soaked through, but the ceiling below showed nothing yet.

Replacement Cost & What’s Included

In Los Angeles, IKO flashing replacement breaks down like this:

• Pipe boot replacement: $280 to $450. One pipe collar, new sealant, shingle re-seat, and haul-away.
• Step flashing replacement (wall run up to 20 linear feet): $500 to $850. Includes removing the bottom course of shingles, pulling the old step flashing and counter flashing, installing new pieces, and re-nailing and sealing.
• Chimney flashing replacement with new counter flashing: $750 to $1,200. This is a bigger job because it involves cutting a reglet into the masonry, folding in new metal, and usually re-pointing a few mortar joints while we’re up there.
• Valley or headwall flashing replacement: $600 to $1,100 depending on run length and slope access.

Every estimate includes the written price before any work starts, per the Garrison Standard. Labor, materials, fasteners, sealant, and disposal are all in the number you sign off on. There are no change orders at the door. The work is covered by the 365-Day Done Right Promise: if the flashing fails within a year of our install, we come back and make it right at no charge. We also pull our own inspections on every flashing job in Los Angeles, Travis included, so the person quoting the work has actually seen the roof.

DIY or Call Us?

Here’s the honest split. If you want to inspect your flashing from the ground or a ladder, use binoculars and look for rust, gaps, or lifted metal. That’s safe and worth doing once a year in Los Angeles, ideally right before the rainy season. But getting onto the roof to replace flashing is another matter. You’re working at the roof edge, or on a slope, often near a chimney or wall transition. A fall from a single-story is a hospital trip, and a fall from a hillside two-story in Mount Washington is worse. Flashing replacement also means lifting shingles, re-nailing into decking, and sealing in a sequence that keeps water flowing the right direction. Get it wrong and the leak comes back worse than before. If you see signs of failing IKO flashing, call (361) 320-9467. We’ll send a background-checked, uniformed technician to look, and you’ll have a written number before anything gets touched.

FAQs